Home » SMD Resistor Calculator

SMD Resistor Calculator


SMD resistors are small electronic components commonly found on circuit boards. Unlike traditional through-hole resistors, most surface-mount resistors use numerical or alphanumeric markings to indicate their resistance value.

These markings can look confusing at first, especially when different coding systems are used. This SMD Resistor Calculator helps you decode common 3-digit, 4-digit, EIA-96, and R-notation markings to find the resistance value quickly.

SMD Resistor Calculator

SMD Resistor Calculator

Enter the marking printed on your SMD resistor to decode its resistance value.

Resistor marking

Enter a 3-digit, 4-digit, EIA-96 or R/K/M notation code.

Try an example:

Typical tolerance values are conventions, not guarantees. Always check the component datasheet when the exact tolerance matters. Some manufacturers use proprietary or special-purpose markings that may not follow these formats.

How to Read SMD Resistor Codes

SMD resistors commonly use three-digit, four-digit, or EIA-96 markings. Some components also use the letter R in place of a decimal point.

1. Three-Digit SMD Resistor Code

In the three-digit system, the first two digits represent the significant figures, while the third digit indicates the multiplier (number of zeros).

For example:

  • 103: 10 × 1,000 = 10,000 Ω (10 kΩ)
  • 472: 47 × 100 = 4,700 Ω (4.7 kΩ)
  • 220: 22 × 1 = 22 Ω

Three-digit markings are commonly used for resistors with standard values and are typically associated with ±5% tolerance.

2. Four-Digit SMD Resistor Code

The four-digit system works similarly, but the first three digits represent the significant figures. The last digit indicates the multiplier.

Examples:

  • 1002: 100 × 100 = 10,000 Ω (10 kΩ)
  • 4702: 470 × 100 = 47,000 Ω (47 kΩ)
  • 2201: 220 × 10 = 2,200 Ω (2.2 kΩ)

Four-digit markings are commonly used for more precise resistor values and are typically associated with ±1% tolerance.

3. EIA-96 Resistor Code

The EIA-96 system is used for precision SMD resistors. It consists of two digits followed by a letter.

  • The first two digits identify a value from the EIA-96 standard table.
  • The final letter indicates the multiplier.

For example:

  • 01C: 100 × 100 = 10,000 Ω (10 kΩ)
  • 68C: 49.9 × 100 = 4,990 Ω (4.99 kΩ)
  • 96D: 976 × 1,000 = 976,000 Ω (976 kΩ)

The EIA-96 system uses 96 standard resistance values. Its letter multipliers include A, B, C, D, E, F, G, and H for increasing values, and X, Y, and Z for fractional multipliers. R and S are also used as alternative markings for the 0.1 and 0.01 multipliers, respectively.

EIA-96 resistors are typically associated with ±1% tolerance.

4. R Notation

Some SMD resistors use the letter R to represent the decimal point. This is particularly useful for low resistance values.

Examples:

  • 4R7: 4.7 Ω
  • R47: 0.47 Ω
  • R010: 0.01 Ω
  • 1R0: 1 Ω
  • 49R9: 49.9 Ω

You may also encounter K and M notation, where the letters represent kilo-ohms and mega-ohms:

  • 4K7: 4.7 kΩ
  • 2M2: 2.2 MΩ

5. Zero-Ohm SMD Resistors

A zero-ohm resistor is used as a jumper to connect two points on a circuit board. It looks like a regular resistor but provides a low-resistance electrical connection.

Common markings include:

  • 0
  • 00
  • 000
  • 0000

These components are useful for PCB configuration, circuit routing, and manufacturing.

Typical SMD Resistor Tolerance

Tolerance indicates how much the actual resistance may differ from its marked value.

Marking systemTypical tolerance
3-digit code±5%
4-digit code±1%
EIA-96 code±1%

These are typical conventions, not guaranteed specifications. Always check the component datasheet when the exact tolerance is important.

Frequently Asked Questions

How do I calculate the resistance of an SMD resistor?

Identify the marking printed on the resistor and enter it into the calculator above. It supports common 3-digit, 4-digit, EIA-96, and R-notation codes.

What does 103 mean on an SMD resistor?

The marking 103 means 10 multiplied by 1,000, giving 10,000 ohms or 10 kΩ.

What does 000 mean on an SMD resistor?

A marking of 000 indicates a zero-ohm jumper. It is used to provide an electrical connection between two points on a circuit board.

What is the difference between 3-digit and 4-digit SMD codes?

A 3-digit code uses the first two digits as significant figures and the third as the multiplier. A 4-digit code uses the first three digits as significant figures and the fourth as the multiplier.

What if my SMD resistor has no marking?

Some very small SMD resistors do not have printed markings. In such cases, you may need to refer to the circuit diagram, component datasheet, or measure the resistance using a multimeter. Avoid measuring resistance while the component is powered.

Note: Some manufacturers use proprietary markings for special-purpose components, including current-sense resistors. These may not follow the common coding systems supported by this calculator.

Related Guides You May Find Useful

Pradeep Augustine Avatar

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Latest Posts